radionics machine Posts

Simple Powered Three Dial Radionics Machine

Simple Powered Three Dial Radionics Machine

Click To Enlarge

Here’s another simple schematic, based on my Super Simple Three Dial, and using the amplifier from the Wishing Machine posted yesterday. The Aerial is an optional extra, and is in no way necessary. You could experiment to see if it increases your output. As before most of this can be done with crocodile clips if you aren’t used to solder and soldering irons. I would add that it would be a good idea to secure and insulate the crocodile clips on the pins of the potentiometer, so that they are secure from pulling lose, and that the tips of the other leads don’t touch creating a short circuit.


Radionics Machine – Wickenden Device V.02

Radionics Machine – Wickenden Device V.02

I have decided to commercially launch Berkana Labs. This is to provide individuals with the opportunity to purchase high quality radionic and aethertronic instruments.

To kick off this commercial venture I have developed the Wickenden Device V.02. The plan was to develop an entry model which packs a punch. I have based the aesthetic design off of the classic wickenden device, but the core of the instrument has had a complete overhaul. The amplifier has been re-imagined, and re-engineered to provide even more power. I wanted to be able to include a few other functions so after a fair amount of research and development I was able to include the following functions:

  • Stochastic resonance subtle signal transfer and amplifier.
  • Automated remedy maker.
  • A vibro potentiser.
  • A proprietary system clearing function.
  • Universal mains voltage power supply.

Radionic Instrument: The Millington Device

I developed this Instrument as a commission. The brief was that a radionics machine was needed, which could be used with Rife frequencies from an audio source, In this case it was Frex software. I got to play around with a few new concepts, and add a loop antenna in the lid.  A few of you who follow my forum posts may remember I developed a twin antenna system for the Moraie. This is the only time a loop antenna has been fully operational in an instrument of my own making, and the results reported by Mr. Millington, the machine’s namesake, have been extremely positive.

There are a few variations to the circuit compared to the Wickenden device. These include a different form of coil winding, in relation to the core crystals, a different amplifier circuit operating in a lower frequency spectrum, and a variation in the radionic output supply stage.

The control panel consists of six Bakelite base 10 dials, another Bakelite intensity adjustment dial located between the top power switch and indicator, and the bottom push button clearing switch and indicator. On the far right of the control panel we have the copper Input Plate to the top, and the Ouput Plate below.



The back of the instrument has been designed to allow for peripheral attachments. The right hand sockets are the inputs, and the left hand the outputs. It’s the reverse of regular audio socket positioning, but it didn’t make radionic sense to do it any other way. I made a simple adapter to allow for a 3.5mm cable connector on the input (not pictured). The output is load protected by a small resistor allowing the potential to feed a patient directly with rife impregnated radionic signals via a couple of low-voltage  electrodes. The layout is very similar in style to the Wickenden device, in fact, the Wickendedn instrument was built with the knowledge I gained from the construction of this device.

I am pleased with how this instrument turned out. I take a lot of pride in constructing these living machines with dedication and meticulous attention to detail. I view the construction of these as an art form and ritual, and the powerful results, and reality manipulation they are capable of speak for themselves.

“We are the real wandmakers” – Sorynzar


Radionic Instrument: The Wickenden Device

I designed and built this radionic instrument with my partner in mind. It is a simple entry level instrument. A powered, resistance, three dial radionics machine, able to take base 10 rates. It has an RF amplifier circuit, and proprietary coil windings and crystal circuit.




It features a power switch, and indicator light on the left-hand side. Copper input plate, and ouput plate. On the far right is the clearing switch, and respective indicator light seen in action below. This fires up a clearing circuit based on an idea by Joseph Max of Aethric Arts Labs.




The final image shows the back of the device, and power/peripheral sockets. These sockets were included so that further functionality could be added to the instrument. For example, a stick pad could be plugged into the output sockets seen here on the left-hand side of the machine. As it stands the operator is expected to use a pendulum to dowse for rates. Most people starting out in the field of radionics find it easier to work with a pendulum rather than a stick/reactor pad. A pendulum is also a standard tool to use with radionic instruments in most radionic associations.




It may seem simple, but this little three dial packs a punch, and along with the unique coil and crystal core, it is highly effective. Currently, it runs on most mains voltages and frequencies across the globe. For a MKII, I intend to install a battery compartment so that it can be used in the field with ease. This would make it an ideal candidate for agricultural work as well. I am pleased how this radionic instrument has turned out, but I feel that it can continue to develop even further.

Update: 11th September 2013

Currently taking orders for the Wickenden Device V.02

The new instrument is £350 GBP + shipping (free UK postage)

Very similar in design to the original Wickenden Device. However, stainless steel plates will be used. The internal electronics are all being updated to make this a much more powerful unit, that really packs a punch. After some last minute requests I have decided that I can offer an alternative battery powered version that will take two 9V battery’s, and which will be accessible from the back of the device. The standard power option is still available and works on a wide range of European and international voltages.

If you are interested, please use the contact form located under “contact” at the top of this page, and I will reply to you as quick as possible.