Radionics Posts

Radionic Instrument: The Millington Device

I developed this Instrument as a commission. The brief was that a radionics machine was needed, which could be used with Rife frequencies from an audio source, In this case it was Frex software. I got to play around with a few new concepts, and add a loop antenna in the lid.  A few of you who follow my forum posts may remember I developed a twin antenna system for the Moraie. This is the only time a loop antenna has been fully operational in an instrument of my own making, and the results reported by Mr. Millington, the machine’s namesake, have been extremely positive.

There are a few variations to the circuit compared to the Wickenden device. These include a different form of coil winding, in relation to the core crystals, a different amplifier circuit operating in a lower frequency spectrum, and a variation in the radionic output supply stage.

The control panel consists of six Bakelite base 10 dials, another Bakelite intensity adjustment dial located between the top power switch and indicator, and the bottom push button clearing switch and indicator. On the far right of the control panel we have the copper Input Plate to the top, and the Ouput Plate below.

 

 

The back of the instrument has been designed to allow for peripheral attachments. The right hand sockets are the inputs, and the left hand the outputs. It’s the reverse of regular audio socket positioning, but it didn’t make radionic sense to do it any other way. I made a simple adapter to allow for a 3.5mm cable connector on the input (not pictured). The output is load protected by a small resistor allowing the potential to feed a patient directly with rife impregnated radionic signals via a couple of low-voltage  electrodes. The layout is very similar in style to the Wickenden device, in fact, the Wickendedn instrument was built with the knowledge I gained from the construction of this device.

I am pleased with how this instrument turned out. I take a lot of pride in constructing these living machines with dedication and meticulous attention to detail. I view the construction of these as an art form and ritual, and the powerful results, and reality manipulation they are capable of speak for themselves.

“We are the real wandmakers” – Sorynzar

 

Radionic Instrument: The Wickenden Device

I designed and built this radionic instrument with my partner in mind. It is a simple entry level instrument. A powered, resistance, three dial radionics machine, able to take base 10 rates. It has an RF amplifier circuit, and proprietary coil windings and crystal circuit.

 

radionic-instrument-1

 

It features a power switch, and indicator light on the left-hand side. Copper input plate, and ouput plate. On the far right is the clearing switch, and respective indicator light seen in action below. This fires up a clearing circuit based on an idea by Joseph Max of Aethric Arts Labs.

 

radionic-instrument-2

 

The final image shows the back of the device, and power/peripheral sockets. These sockets were included so that further functionality could be added to the instrument. For example, a stick pad could be plugged into the output sockets seen here on the left-hand side of the machine. As it stands the operator is expected to use a pendulum to dowse for rates. Most people starting out in the field of radionics find it easier to work with a pendulum rather than a stick/reactor pad. A pendulum is also a standard tool to use with radionic instruments in most radionic associations.

 

radionic-instrument-3

 

It may seem simple, but this little three dial packs a punch, and along with the unique coil and crystal core, it is highly effective. Currently, it runs on most mains voltages and frequencies across the globe. For a MKII, I intend to install a battery compartment so that it can be used in the field with ease. This would make it an ideal candidate for agricultural work as well. I am pleased how this radionic instrument has turned out, but I feel that it can continue to develop even further.

Update: 11th September 2013

Currently taking orders for the Wickenden Device V.02

The new instrument is £350 GBP + shipping (free UK postage)

Very similar in design to the original Wickenden Device. However, stainless steel plates will be used. The internal electronics are all being updated to make this a much more powerful unit, that really packs a punch. After some last minute requests I have decided that I can offer an alternative battery powered version that will take two 9V battery’s, and which will be accessible from the back of the device. The standard power option is still available and works on a wide range of European and international voltages.

If you are interested, please use the contact form located under “contact” at the top of this page, and I will reply to you as quick as possible.

 

 

Radionics Schematic: Super Simple Three Dial

 

Presented here for your delectation is a super simple three dial radionics schematic. There is no techno jargon, or standard schematic imagery. The circuit is simple as shown. The black lines represent wires, and their connections. The bottom row of wiring simply shows that the last post on each potentiometer is connected to the last post on the next.

This type of circuit is also known within radionics as a passive resistance circuit. There are no coils, crystals, or amplifiers within this circuit, but that does not detract from its raw power. Generally, this circuit can be used to copy homeopathic remedies, or for imbuing a witnesses sample with a particular trend. For the latter, the witness sample would be placed on the output, and the trend would be placed on the input. The trend could take the form of a remedy, written or pictorial intention, etc. For use in agricultural radionics for instance; fertilizer, or pesticides could be placed on the input plate, and their rates dowsed for with a pendulum.

What you will need:

 

  • Two copper discs, or copper sheets. Copper is not necessary, but it by far the best candidate for our purpose. If you are struggling to find copper, you can use brass, aluminium, or stainless steel as a last resort. If you are extremely lucky, you can even use gold, or silver sheet!

 

  • Three potentiometers. These are “10K linear potentiometers” run an internet search, or look on places like ebay for these components. Failing that try your local electronics supplier such as Maplins, or Radio Shack.

 

  • You will need a length of wire to wire up the potentiometer. Some researchers use solid clear enameled copper wire, but I find regular bell wire or equipment wire works just as well. Again, you can get some regular stranded single core wire from hardware stores or online. You will probably need less than a meter for this, but just to be on the safe side, and to have some surplus for a future project, get hold of a meter, or several feet worth.

 

  • You will also need something for stripping the wire; a pair of wire cutters can be used once you get the hang of it, or a craft knife.
  • In order to connect the wires to the potentiometers, you will need to Solder. For a beginner with no electronics experience, this is often a stumbling block. You can get hold of cheap soldering irons on the internet. You will only need something rated at 25-30W. Get yourself a book on soldering for beginners, and a reel of silver based solder. It really is quite easy to do, and once you learn this new skill you can use it for future projects.If this still puts you off, there is a product called “Wire glue” which will literally allow you to glue the wires to the potentiometers and plates. Failing that you could use some electrical tape. I wouldn’t advocate this, but it is possible as a last resort.

 

  • You will also need some type of box to mount everything in. Charles Cossimano suggests a shoe box. This can work well if you are on a budget. Personally, I use wooden boxes where possible. However, if you really have to, an ABS plastic box will work o.k.

 

  • In order to mount the potentiometers. You will require a drill, and selection of drill bits.
  • Finally; x4 bolts x8 washers, and at least four nuts. To top this off three potentiometer dials. Again, these are available from places such as Ebay, and Radio Shack, etc.

 

Once you have all your components you can begin to build to the above diagram. You should have chosen an enclosure/box which will allow you enough room to mount everything on one surface, usually the top. If it doesn’t, not to worry; some people will mount the plates on the top surface, and the dials on one of the sides to make more room.

 

It’s quite simple from here on in. Use your intuition, and build an instrument which you find visually and aesthetically appealing, as this will increase its potential. You are imbuing the device with your own power, use it wisely.

 

This information is free to copy and distribute. All I ask as my copyright condition is that you attribute the work back to BerkanaPath.com. These posts and diagrams take a great amount of work, and it is saddening when people abuse the work of others. This is why I am being forced to watermark all of my intellectual properties. Thank you for understanding.

 

 

Copen Restoration Project 1

I have been fortunate to acquire three original Bruce Copen Radionic Instruments. Unfortunately, they were in quite a state when I received them. The images below are of a nine dial base 10 resistance instrument. I can’t seem to find any information on this, but judging by the pass dates on the old Colvern potentiometers, it is from the early to mid 50s. Looking at the general grime build up and rust on the nickel fittings, I can only assume it had been stored in damp conditions for a number of years, most likely in a shed or barn. It is sad to think that these impressionable instruments were left neglected, their original owner no longer able to care for them. At one point, they were used extensively to manufacture homeopathic remedies. A lot of the surviving vials came with the lot. However, I have no use for vintage remedies so have stored them away. If anyone is interested in the vials, please get in touch.

 

I am slowly, working my way through the restoration, and am making good progress. I have decided to tackle this nine dial instrument first, as it is the easiest. Currently, I have fully cleaned up the casing, and replaced the fixings with brand new nickel latches and hinges from the original company. I have also replaced the leather strap handle on the front. The inside lid has been lined with red card, reflecting the original intentions of using paper, which was too damp and dirty to re-use. I will upload some new photos on another post over the next few weeks. Currently, I’m working on the control panel. Sadly only one of the original potentiometers is in full working order, luckily it is the one which can’t be easily replaced. Copen’s wiring is the most unusual. On this nine dial instrument, you have three logarithmic carbon track 1Megaohm pots, then one 50k linear carbon track. The remaining five in the sequence are Colvern wirewound’s which go from 100k, 10k, 1k, 100R, and 10R I can see the logic in the last five as the resistance steps down, but it’s almost as if Copen has rummaged in his parts box to make up the first four in the stage. This initial 3-4M of resistance is seen in the other instruments I have. It would make more sense if they stepped down like the others and were all linear. It’s a mystery!

 

The neon lamp on this instrument is wired in an unusual manner, so that it is turned off when the power is in the off position. I suspect the original owner fiddled with the wiring at some point in its history. I intend to rewire the circuit with the same type of wire Copen used, and replace the shot pots, but leave the unusual configuration intact, aside from the neon lamp which I will change to reflect the correct way of operation as seen in the other instruments I have. I look forward to presenting the fully restored instrument to you in a new article.

 

 

Update: 18th April

Some of the potentiometers aren’t as damaged as I originally thought. A great deal of tuner cleaner, and they appear to work o.k. Its not to my usual high standards, but what can you expect from components that are sixty odd years old?! The resistances are all o.k and within the manufacturer’s tolerance range, it’s just the movement  is not as fluid or consistent as I would have liked, and this may present a problem when tuning the instrument. I have several wirewounds en route, so it should not be a problem. I would like to keep the originals where I can.

Furthermore, the card lining the lid has begun to peel away. I may just go and Araldite a sheet of thin felted, or vinyled wood to the lid to get around this problem. In any case, I will stick with the red as it compliments the red leather of the case.

 

The clogged up dials on the control panel are clearly visible in this image. It has since been completely taken apart and cleaned. The dials look as good as new now.

Bruce Copen

Copen dowsing for the stone of destiny

Bruce Copen was a pioneer of radionics. Following on from the works of Abram, Drown and De La Warr. Copen did not start his foray into radionics until the late 1940’s. It was soon after arriving back in England after his service during the second world war that he begun to develop the model Y radionic soil analyser. This was first released to the public in 1947. I have acquired a model Y, which has part dates from the late 50’s so it was in production until at least the 60’s. As for whether it was continued, I am unsure.

In the late 60’s the Mark II radionic computer was released. This marked a string of radionic computers. Each later model being updated by Copen to reflect his ever continuing research, and advancements in the field of radionics, and technology.

Bruce Copen was much more than a radionic instrument manufacturer. He was a Doctor of philosophy and literature, and an avid writer from a young age. During his youth, he wrote a number of stage plays and books of poetry. This was later carried over to written works on the subject of radionics, radiesthesia, and various healing modalities. His contribution to the world of adult education was honoured by him being initiated as Knight of the sovereign order of St. John of Jerusalem.

Mr. Copen was also the founder for the British Radionics Association, and Editor of a number of journals, namely the British Journal of Radiesthesia, Natural Therapeutics, and Seeker. He also founded the International College of Radionics.

Bruce Copen was a renowned dowser. His skills were called upon when the Coronation stone “stone of destiny” went missing from Westminster abbey on Christmas day 1950. His efforts in locating the stone received media attention. Unfortunately, the stone was not located, by any method. A year later it turned up in Scotland. Perhaps Mr. Copen’s endeavours had an unperceived effect upon its reappearance?

In the 60’s, Copen developed the first colour healing instrument. This device was unique in that it held colour rates and transmitted/broadcast them radionicaly rather than using the photon transfer method.

Bruce Copen continued to develop his ideas and models throughout the 20th century. He unfortunately died suddenly at home in 1998.

It was his last wishes that his lab be formed into a company. After his death, Harold Rauer became manager of Copen labs ltd. The later models were far removed from anything Copen would have personally developed. These Rauer produced models consisted of the MARS models. A mistake I feel was to digitalise the instruments. Radionics in its most effective form is purely analogue, and Copen’s use of these components in his instruments reflect the nature of radionics.

There is conflicting information as to whether Bruce Copen laboratories is still operating. Some sources have it listed that the company ceased trading in 2010.

Bruce Copen designed and built quality radionic and therapeutic instruments throughout his life. Unfortunately, his skill is now lost to us, but we can remember him for the man and pioneer he was.

Bruce Copen (1923- 1998)